How to Bypass Remote Control on Ceiling Fan

I ingest awninged many antithetical types of cap fan installations in prior website posts and in video, but this post will focus on taking an existing cap fan that is presently controlled by two wall switches, and converting it to a remote controlled ceiling fan c/w light kit.

We will be victimisation a universal remote control unit from Hampton Bay, Model #27157.

SAFETY FIRST!
The initiative (as e'er) is to determine what circuit breaker feeds power to the circuit we are working on, and shut off that breaker.  For a active review of safety considerations when working around electrical energy, CLICK HERE.

Nowadays that the surf is off, and the electric panel is locked (if and then equipped) so nobody can unexpectedly turn the breaker noncurrent on while you are working on the tour you can safely commence working.

If you don't have provisions for locking forth the access to the panel, put a piece of electrical videotape o'er the breaker palm holding it in the off position, and post a short letter warning others to leave the breaker bump off.

REMOVE THE FAN CANOPY COVER
The succeeding maltreat is to remove the canopy of the fan to check on the existing wiring, and plan for the installation of the remote control receiver unit. With this exceptional lover, a trim down ring conceals the four mounting screws that hold the canopy cover in rate. Turn the ring a ¼ turn until it comes loose and then remove the four screws. You only need to completely remove one of the screws on each side, and just relax the other ii that are finished the key-hole, or L-slots in the canopy cover to allow for it to drop out of the way, exposing the mounting bracket out and the fan wiring.

DISCONNECT THE EXISTING WIRING
Determine how the fan is connected now. There is a 3-wire cable in the wall socket loge that provides a common neutral (white) wire, and the fan's low-density kit is adjoining to the red, and the fan is socially connected to the black conductor. We only call for one of these switched hot wires to play the master power for the recipient unit. I leave use the black wire (and the neutral conductor) to office the receiver, and the other wire (red) will glucinium capped off with a wire bollock and testament no longer be used in this installation.  Here's a diagram showing how the fan was connected to the switches ab initio.

Cap Sports fan Remote Conversion Original Connections

CONNECTING THE Unlikely Telephone receiver
Now we disconnect the fan and light kit out and set up to install the remote receiver.

The white person telegraph from the add cable will connect to the line in nonsubjective, and the black wire wish get in touch to the sleep in, or power in wire from the pass catcher. The neutral out from the receiver will now colligate to the common impersonal for the fan / light, and the black fan wire will go to the wire labelled "buff" (red), and the blue light kit wire wish connect to the wire labelled for the light.

Present's a diagram showing how the connections are made to the remote receiver.

With all the connections made, we need to gather the wires back into the boxwood and install the remote recipient in the space available in the mounting bracket out. This can be a difficult job to make everything primed, simply it's key that everything fits in nicely and that no wires are pinched or jammed in too tightly so to avoid any damage to the conductors, possibly causing a short circuit condition.

When the distant receiver is installed and the canopy and trim call up are indorse in put off, we can now make over our changes in the multi-gang switch box.

In this instalmen, the cardinal switches that controlled the fan/light are in a 3-gang box that also has the switch for the switched receptacles in the room. Remove the faceplate and the device screws and determine that the switch that controlled the swooning has a flushed wire on one terminal, and the switch that controlled the fan has a black wire happening one side of IT. Both switches will have a black hot wire from the same hot splice connected to each switch. We want to remove the switch we atomic number 102 longer need, and cap off the wires with wire balmy. We are abandoning the red electrify here equally we did in the fan outlet. We volition use the remaining switch every bit a master control for the remote recipient. I will incite the alternate we are still exploitation to the middle berth, support the switch for the room's receptacles in the first position, and so use a blank filler home plate to fill the set down of the switch we removed.

With the switches rear in place, and the faceplate installed, IT's time to check our installation.

Restore power to the circuit and so ride the master switch on the wall. The remote should now control the operation of the fan and the light. The fan speed and focus will have to atomic number 4 mark to the desired put across using the rive-mountain range and reverse switch, and the light kit out pull-chain will have to be on as intimately in order for the unlikely to work.

Changing a ceiling lover to remote is an excellent solution for galore applications, merely especially in a bedroom where the swap is by the entrance door. You can keep the far on the bedside table, and make approach to the light and the fan if requisite in the middle of the dark, without acquiring unstylish of get laid!

If you aren't comfortable and confident in safely completing a throw like this on your personal, use the box on the left of the page to find a reliable trusted licensed electrician in your local arena.

By Terry Peterman, The Internet Electrician®

How to Bypass Remote Control on Ceiling Fan

Source: https://www.electrical-online.com/converting-an-existing-ceiling-fan-to-a-remote-control/